Industrial equipment. Informed decisions.8483454@gmail.com
IndustryApex

Equipment category

Energy & electrical
Buying guides & project requirements.

Define solar, storage, charging, power and control projects using measured loads, interfaces, operating conditions and exact destination requirements.

  • Load profiles, duty, input/output ratings and system limits
  • Grid, communications, battery, motor or controller interfaces
  • Exact project documents, installation and acceptance responsibility
  • Complete installed scope, monitoring, spare parts and service
Clear filters

Showing 49–72 of 298 equipment guides.

AKSA Power Generation Generator paralleling and synchronization switch cabinet (manual Figure 2) generator synchronization panel reference equipment
ENERGY & ELECTRICAL

Generator synchronization panel

A generator synchronization panel coordinates qualified sources before closing the appropriate switching devices and sharing load where designed. It is a system-control assembly, distinct from a simple transfer switch that avoids intentional source paralleling. Parallel generators require synchronization and load-sharing controls.

Explore the buying guide

Reference: AKSA Power Generation Generator paralleling and synchronization switch cabinet (manual Figure 2)

STIEBEL ELTRON WPF 66 ground source heat pump reference equipment
ENERGY & ELECTRICAL

Ground source heat pump

A ground-source heat pump transfers heat between a qualified ground or brine loop and a building or process-water circuit. Its performance depends on both sides of the thermal system, distinguishing it from an air-source unit or a heater selected only by output temperature. Ground loop and geotechnical conditions distinguish source-side design.

Explore the buying guide

Reference: STIEBEL ELTRON WPF 66

Ballard FCwave module hydrogen fuel cell power system reference equipment
ENERGY & ELECTRICAL

Hydrogen fuel cell power system

A hydrogen fuel-cell power system converts qualified hydrogen electrochemically into DC power and associated heat, with the balance of plant and power conversion needed for the receiving load. A fuel-cell module reference does not by itself define a complete installed power station. Fuel supply and electrical integration govern stationary electrochemical generation.

Explore the buying guide

Reference: Ballard FCwave module

Chromalox Screwplug immersion heater immersion process heater reference equipment
ENERGY & ELECTRICAL

Immersion process heater

An immersion process heater places qualified electrical heating elements directly into a liquid, tank or other designed medium. Its buying boundary is local element-to-medium heat transfer, distinct from a packaged circulation heater with its own flow vessel. Wetted materials and surface heat flux depend on process fluid.

Explore the buying guide

Reference: Chromalox Screwplug immersion heater

Victron Energy Skylla-IP65 industrial battery charger reference equipment
ENERGY & ELECTRICAL

Industrial battery charger

An industrial battery charger supplies a controlled charging profile matched to a specified battery and application. It is distinct from a general DC power converter because charge stages, limits and battery condition influence the required behavior. Charge profile and battery interface govern stationary charging.

Explore the buying guide

Reference: Victron Energy Skylla-IP65

Chromalox CPM self-regulating heating cable industrial heat tracing system reference equipment
ENERGY & ELECTRICAL

Industrial heat tracing system

An industrial heat-tracing system supplies distributed heat along piping or equipment to maintain a specified temperature or prevent freezing. It is a site-designed thermal system including insulation and controls, distinct from a single tank or circulation heater. Pipe temperature maintenance requires insulation and zone design.

Explore the buying guide

Reference: Chromalox CPM self-regulating heating cable

Chromalox Metal-sheathed process radiant heater industrial infrared heating system reference equipment
ENERGY & ELECTRICAL

Industrial infrared heating system

An industrial infrared heating system transfers radiant energy to a product surface through selected emitters, reflectors and geometry. The useful heating depends on the product's absorption and exposure, distinguishing it from primarily convective air or liquid heating. Radiant coupling and product absorption determine surface heating.

Explore the buying guide

Reference: Chromalox Metal-sheathed process radiant heater

American Plating Power Water-cooled SCR rectifier cabinets — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Industrial rectifier power supply

An industrial rectifier power supply converts AC input into controlled DC for a defined industrial load. The load process, output regulation and fault behaviour determine the selected power conversion arrangement. Start with dc voltage range and dc current and duty, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: American Plating Power Water-cooled SCR rectifier cabinets

EcoInnovation PowerSpout PowerSpout PLT Pelton hydro turbine — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Micro hydro turbine generator

A micro hydro turbine generator converts the energy of flowing water into electrical output at a defined site. The turbine, water supply, generator and controls must be engineered together. Start with net head and seasonal flow, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: EcoInnovation PowerSpout PowerSpout PLT Pelton hydro turbine

Mecc Alte PTO tractor-driven generator unit — actual manufacturer equipment reference
ENERGY & ELECTRICAL

PTO generator

A PTO generator uses tractor power through a compatible power take-off drive to generate electricity. The complete set includes the speed conversion, frame, controls and electrical protection required for the intended use. Start with tractor pto speed and power and electrical load list, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Mecc Alte PTO tractor-driven generator unit

B&K Precision 9805 programmable AC power source — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Programmable AC power source

A programmable AC power source supplies controlled voltage and frequency to equipment under test. It supports repeatable electrical testing within a defined source envelope rather than serving as an unrestricted utility replacement. Start with output voltage and phases and frequency range, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: B&K Precision 9805 programmable AC power source

Avtron 2705 resistive load bank actual equipment configuration reference
ENERGY & ELECTRICAL

Resistive load bank

A resistive load bank converts electrical power into heat to provide a controlled load for testing power systems. Its resistive duty does not reproduce every reactive or nonlinear load. Start with source voltage and phases and frequency, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Avtron 2705 resistive load bank

Cavotec PowerExtend shore connection cable system — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Shore power connection system

A shore power connection system transfers electrical power between a port installation and a vessel while coordinating connection, protection and operation. Cable handling is one part of the complete shore-to-ship system. Start with vessel load and supply and voltage and frequency, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Cavotec PowerExtend shore connection cable system

Viessmann Vitosol 200-FM flat-plate collector — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Solar thermal collector system

A solar thermal collector system captures solar heat for a defined water or process heating duty. It requires hydraulic, storage and control design in addition to the collectors. Start with heat load profile and required temperatures, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Viessmann Vitosol 200-FM flat-plate collector

Sinepower SINESFC 250-400 kVA static frequency converter — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Static frequency converter

A static frequency converter changes electrical frequency electronically to supply a load at the required output conditions. It differs from a voltage-only transformer or stabilizer. Start with input supply and output voltage and frequency, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Sinepower SINESFC 250-400 kVA static frequency converter

Vertiv Liebert GXT5 rack tower UPS actual manufacturer equipment reference
ENERGY & ELECTRICAL

Uninterruptible power supply

An uninterruptible power supply supports defined loads during input disturbances using power conversion and energy storage. Backup duration and continuity depend on the complete configured system and load. Start with critical load and power factor and inrush, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Vertiv Liebert GXT5 rack/tower UPS family with battery arrangement

Vestas Onshore wind turbine installation actual equipment configuration reference
ENERGY & ELECTRICAL

Wind turbine system

A wind turbine system converts wind energy into electricity through a site-specific turbine and electrical installation. Site wind and structural conditions determine suitability and expected energy. Start with wind resource and turbulence and extremes, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Vestas Onshore wind turbine installation

ABB PQF active harmonic filter cabinet family actual equipment reference
ENERGY & ELECTRICAL

Active harmonic filter

An active harmonic filter injects compensating current to reduce selected electrical disturbances in a defined network. Selection should follow measurements and a study of the installation. Start with network voltage and arrangement and baseline harmonics, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: ABB PQF active harmonic filter cabinet family

ABB SACE Emax 3 air circuit breaker — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Air circuit breaker

An air circuit breaker switches and protects a low-voltage power circuit within a specified assembly. The device and trip settings must be coordinated with the network and downstream protection. Start with circuit voltage and continuous current, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: ABB SACE Emax 3 air circuit breaker

Ortea Next Orion electromechanical voltage stabiliser — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Automatic voltage regulator

An automatic voltage regulator for supply stabilization maintains a defined output voltage as input and load conditions vary. This guide concerns incoming-supply stabilization, separate from alternator excitation controls. Start with input voltage envelope and output band, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Ortea Next Orion electromechanical voltage stabiliser

Torytrans AT series reversible three-phase autotransformer — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Autotransformer voltage converter

An autotransformer voltage converter uses a shared winding arrangement to change voltage. It generally does not provide the galvanic isolation associated with a separate-winding transformer. Start with input and output voltage and phases and frequency, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Torytrans AT series reversible three-phase autotransformer

ABB WavePro-II busbar trunking section actual equipment reference
ENERGY & ELECTRICAL

Busbar trunking system

A busbar trunking system distributes power through a modular enclosed conductor assembly. Routing, joints and tap-off units must be selected as a compatible system. Start with voltage and current and fault level, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: ABB WavePro-II busbar trunking section

SGB-SMIT Cast resin dry-type transformer — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Cast resin dry-type transformer

A cast resin dry-type transformer transfers power through resin-encapsulated windings without a liquid insulating tank. Cooling, enclosure and site conditions remain essential to the installed thermal and insulation design. Start with voltage ratio and power and load profile, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: SGB-SMIT Cast resin dry-type transformer

Ormazabal miniblok compact secondary substation — actual manufacturer equipment reference
ENERGY & ELECTRICAL

Compact secondary substation

A compact secondary substation combines medium-voltage equipment, a transformer and low-voltage distribution within an engineered enclosure. Each compartment and interface must suit the network and site. Start with utility supply requirements and transformer duty, then agree the configuration and the evidence required for acceptance.

Explore the buying guide

Reference: Ormazabal miniblok compact secondary substation

Build a comparable request

Start with the work your equipment needs to do.

Share the application, required output, destination, utilities, quantities and planned timing. For OEM / ODM projects, include the branding, configuration or engineering changes, sample approval and acceptance requirements.

Discuss your project ↗Prepare an OEM / ODM brief ↗

Practical buying decisions

Guides for this equipment category.

More buying guides ↗
Energy & electrical

Air to water heat pump radiator compatibility: Buyer Decision Guide

Existing radiators can work with air to water heat pumps when assessed against the proposed supply temperatures and building heat demand. Request emitter output calculations at the heat pump's intended delivery temperature, verify system flow rates and check whether the radiators meet design-day heating requirements.…

Applications & selection · 5 min read
Read the guide
Energy & electrical

Solar tracking system: RFQ Checklist and Quotation Review

A comparable solar tracking system quotation starts with module layout, terrain, geotechnical data. Record the required result, site interfaces and acceptance evidence in one revision-controlled RFQ. IndustryApex engineers use these inputs to define the equipment, integration and OEM/ODM scope for your project.

RFQ & acceptance · 4 min read
Read the guide
Energy & electrical

Solar mounting structure: RFQ Checklist and Quotation Review

A comparable solar mounting structure quotation starts with module and clamp data, array layout, wind and snow. Record the required result, site interfaces and acceptance evidence in one revision-controlled RFQ. IndustryApex engineers use these inputs to define the equipment, integration and OEM/ODM scope for your…

RFQ & acceptance · 4 min read
Read the guide
WhatsApp